智能制造網>產品庫>儀器儀表>物性測試儀器>試驗機>>辦公椅耐久性試驗機,辦公家具試驗機，家具檢測儀器

辦公椅耐久性試驗機,辦公家具試驗機，家具檢測儀器

參考價

面議

具體成交價以合同協議為準

公司名稱東莞優力精密機械有限公司
品牌
型號
所在地東莞市
廠商性質
更新時間2023/5/19 22:27:55
訪問次數244

產品標簽:

辦公家具檢測儀器椅桌耐壓強度試驗機

在線詢價收藏產品點擊查看電話

聯系我們時請說明是智能制造網上看到的信息，謝謝!

索取相關資料

公司介紹主營產品

展開顯示更多內容

產品簡介在線詢價

辦公椅耐久性試驗機,辦公家具試驗機，家具檢測儀器符合標準：GB/T10357./EN1728./ANSI BIFMA X5.1./BS4875/BS EN527/BS EN581/BS EN1335.等

辦公椅耐久性試驗機,辦公家具試驗機，家具檢測儀器產品信息

辦公椅耐久性試驗機,辦公家具試驗機，家具檢測儀器

符合標準：GB/T10357./EN1728./ANSI BIFMA X5.1./BS4875/BS EN527/BS EN581/BS EN1335.等

椅子測試儀器

測試項目：座面，靠背。

座椅座面的試驗方法

Test Method for Seat Chair and seat surface:

1.座面的靜載荷試驗：通過加載塊垂直向下施加一定力量于加載點上并保持至少10秒。并反復進行10次。

Seat Surface Static Load Test:

vertically down through the loading block to exert force on the load point and keep at least 10 seconds. And repeated 10 times

2.座面的疲勞試驗：通過加載墊，將950N的力和規定的次數垂直向下重復施加在座面加載點上。加載速率為每分鐘不超過40次。

Fatigue test of the seat: by loading pad, put 950N force and the specified times to repeat vertically down impose to the load point of the seat surface. Loading rate no more than 40 times per minute

3.座面的沖擊試驗：將一塊泡沫塑料放在座面上，然后把座面沖擊器置于規定的高度，使其自由跌落，沖擊加載部位各10次。

Impact test of the seat: put a piece of foam on the seat surface, then place the impactor of the seat in a specified height and make it fall freely. impact loading site 10 times each.

座椅靠背的試驗方法：

Test methods for back of the chair

1.座背的靜載荷試驗：用擋塊靠住椅和凳子的腳上。然后將規定的平衡載荷施加于座面加載點上。再將規定的力沿著與椅背垂直的方向通過加載墊施加于加載點上。每次至少保持10秒。并反復進行10次。

Static Load Test for back of the chair: put the baffle on the chair leg. Then impose the specified balance loading to the load point of the seat. And then provides the force perpendicular to the direction along the back pad by loading imposed on the load point. To keep at least 10 seconds each. And repeated 10 times.

2.座背的疲勞試驗：用擋塊靠住椅或者凳子的腳上，然后將950N的力垂直施加在座面加載點上，再通過椅背加載塊，將330N的力按規定的次數施加在椅背的加載點上。加載速率為每份鐘不超過40次。

Fatigue test of the seat back : use the block fixed the feet of the chair and then impose the 950N force vertically to the surface load point, through the back loading block. Impose 330 N force with specified times to the back loading site. Loading rate no more than 40 times per minute.

桌子測試儀器

測試項目：桌子的穩定性和桌面衝擊。

1、 垂直負載下的穩定性試驗：

Stability test of the vertical load

把試件放在試驗基面上。在其zui不穩定桌邊中心離邊沿向內50mm桌面處通過加載墊垂直向下逐漸加力到規定的力值或者至少試件至少有一個桌腳離地為止。

Place test specimen on the base surface. Impose the force to the table in its center from the edge of the most unstable inward 50mm desktop vertically down through the loading pad gradually with augmented the value or at least one specimen legs up off the ground.

2.垂直和水平加載穩定性試驗：

Vertical and horizontal load stability test

把試件放在試驗基面上。用擋塊擋住試件zui不穩定邊的桌腳。防止試件在試驗中移動。在該邊中心離邊沿向內50mm桌面處通過加載墊垂直向下施加100N的力。同時在該邊中心桌上向外施加一個水平力。逐漸增加該力到規定值或者至少有一個桌腳離地為止。

Put the specimen on the test-based surface. With the block blocking the most unstable side of the specimen legs to prevent the test specimen to move. The edge center from the edge inward 50mm desktop department ，exert downward vertical 100N force by loading pad. While exert a level force on the center desk of the edge, increase gradually to a specified value or one leg near to the floor at least.

3.垂直靜載荷試驗：

Vertical static load test

在桌面易于發生破壞的位置，按規定的力通過加載墊，垂直向下重復施加10次。每次至少應保持10秒。

On the most easy damaged position of the desk surface , to impose the specified force by loading pad, vertical put down repeated 10 times. Keep 10 seconds at least.

Desktop sustained vertical load test

椅子測試儀器

測試項目：座面衝擊

座面的沖擊試驗：將一塊泡沫塑料放在座面上，然后把座面沖擊器置于規定的高度，使其自由跌落，沖擊加載部位各10次。

Impact test of the seat: put a piece of foam on the seat surface, then place the impactor of the seat in a specified height and make it fall freely. impact loading site 10 times each.

關鍵詞：試驗機家具試驗機