當前位置：上海榮計達儀器科技有限公司>>油漆涂料檢測儀器>>磨平機

磨平機

Name: 磨平機
SKU: QPM
Availability: InStock

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號QPM

品牌

廠商性質其他

所在地上海市

在線詢價收藏產品查看聯系電話

聯系方式：王林查看聯系方式

更新時間：2024-01-06 10:42:39瀏覽次數：282次

聯系我時，請告知來自智能制造網

產品分類 品牌分類

暫無信息

上海榮計達儀器科技有限公司

經營模式：其他

商鋪產品：391條

所在地區：

聯系人：王林

詢價 給他留言

產品簡介

可作顏料、涂料、油墨行業專用的物理性能檢驗儀器。整機結構緊湊，外觀簡潔，轉數和負荷變換方便，下班盤裝拆簡便。采用液晶屏顯示，參數設置方便。平磨儀是國家標準GB5211.19《著我顏料相對著色力和沖淡的測定目視比較法》中的儀器。

詳細介紹

一、產品簡介：是檢測儀器，可作顏料、涂料、油墨行業專用的物理性能檢驗儀器。整機結構緊湊，外觀簡潔，轉數和負荷變換方便，下班盤裝拆簡便。采用液晶屏顯示，參數設置方便。平磨儀是**標準GB5211.19《著我顏料相對著色力和沖淡的測定目視比較法》中的儀器。

1. Product introduction: It is a testing instrument that can be used as a special physical performance testing instrument for the paint, coating, and ink industries. The whole machine is compact in structure, simple in appearance, convenient to change the number of revolutions and load, and easy to install and disassemble off-duty trays. It adopts LCD screen to display, convenient parameter setting. The flat grinder is an instrument in the ** standard GB5211.19 "The Visual Comparison Method for the Determination of the Relative Tinting Strength and Dilutedness of Paints".

二、技術參數：

★磨盤直徑：240mm

★荷載： 43 kg 64kg 100kg

★砝碼重量： 1.75kg 3.5kg 6.42kg

★電源電壓： 220VAC 50HZ

★ 玻璃盤轉速:75 轉/分±5轉/分

★設定圈數顯示范圍：1~9999

★運轉圈數顯示范圍：0~9999

★累計次數顯示范圍：0~9999

★外形尺寸： 580*360*480mm

★重量：約80kg

★電動機功率：0.75kw

2. Technical parameters:

★Diameter of Grinding Disc: 240mm

★Load: 43 kg 64kg 100kg

★The weight of the weight: 1.75kg 3.5kg 6.42kg

★Power supply voltage: 220VAC 50HZ

★ Rotation speed of glass plate: 75 rpm ± 5 rpm

★Display range of setting laps: 1~9999

★Display range of the number of revolutions: 0~9999

★Display range of accumulated times: 0~9999

★Dimensions: 580*360*480mm

★Weight: about 80kg

★Motor power: 0.75kw

三、操作步驟：

★將定量的試樣和調和劑放在下磨盤上，用調刀調和成漿，然后將調和好的漿移到下磨盤的**位置，并放下上磨盤，使定位軸芯與定位塊扣上，再將偏心手柄向下板，掛上所需砝碼。

★合上控制器的電源開關時，蜂鳴器發出“滴"的一聲。

★液晶屏顯示開機畫面：

★按鍵盤上的“設定"鍵進入設定圈數的萬位，此時萬位在閃爍，按下“▲"鍵萬位數值加1，按下“?"鍵循環移一位。按下“確定"鍵確定設定圈數，進入功能操作。但設定圈數不為0，否則顯示“輸入設定圈數"，重新設置。在設定圈數期間不能按下功能鍵，否則顯示設定圈數，重新設置。若“確定"鍵按下發現設定圈數有誤可按下“設定"鍵重新設置。若確定設定圈數正確，按下“運轉"鍵，此時電動機開始運行。每轉動一圈。“運轉圈數"自動累計加1。當運轉圈數和設定圈數相同時，電動機自動停止運轉，此時蜂鳴器發出“嘀嘀嘀"的報警聲，“累計次數"自動加1。此時扳動偏心手柄，把磨盤上、下分離，將定位手柄往外拉，同時向上推起，打開上磨盤，觀察試樣。

★若按照上一次設定的圈數再運轉一次，**直接按“運轉"按鍵；如要在中途停機，則可按“停止"按鍵。若“清零A"則“運轉圈數A"計數器會自動清零；若“清零B"則“累計次數B"計數器會自動清零，于此同時會發出“嘀"的一聲。要再繼續工作只需按“運轉"按鍵，機器將繼續運轉，直到運轉到設定的圈數為止。

★若機器要長時間運轉，則應停止計數器計數。此時“運轉圈數"會顯示“STOP"；假如不想長時間運轉，**再按一次“停止計數"按鍵，機器**恢復到原來計數狀態。

★若機械運轉過程中按“設定"鍵，整機將停止運行。同時“設定圈數"萬位閃爍、“清零A"和“清零B"的數值。

★如需水冷，則接通上磨盤的水嘴。

3. Operation steps:

★Put the quantitative sample and blending agent on the lower grinding disc, use the knife to adjust the pulp, then move the blended pulp to the ** position of the lower grinding disc, and put down the upper grinding disc, so that the positioning shaft core and the positioning block are buckled , Then move the eccentric handle to the lower plate, and hang the required weights.

★When closing the power switch of the controller, the buzzer will make a beep.

★The LCD screen displays the boot screen:

★Press the "Set" button on the keyboard to enter the ten-thousａnd digit of the set number of laps. At this time, the ten-thousａnd digit is flashing. Press the "▲" key to increase the ten-thousａnd digit value by 1, and press the "?" Press the "OK" key to confirm the set number of laps and enter the function operation. But the set number of laps is not 0, otherwise it will display "input set number of laps" and reset. The function key cannot be pressed during the setting of the number of laps, otherwise the set number of laps will be displayed and reset. If you find that the number of laps is wrong when you press the "OK" button, you can press the "Set" button to reset it. If you are sure that the set number of laps is correct, press the "Run" key, and the motor will start to run at this time. Every turn. The "number of revolutions" automatically accumulates by 1. When the number of running laps is the same as the set number of laps, the motor will automatically stop running. At this time, the buzzer emits a "di di di" alarm sound, and the "accumulated number of times" automatically increases by 1. At this time, pull the eccentric handle to separate the upper and lower grinding discs, pull the positioning handle outwards and push up at the same time, open the upper grinding disc, and observe the sample.

★If you run again according to the number of laps set last time,** directly press the "Run" button; if you want to stop in the middle, you can press the "Stop" button. If "Clear A", the "Running Number A" counter will be automatically cleared; if "Clear B", the "Accumulative Times B" counter will be automatically cleared, and a beep will be emitted at the same time. To continue working, just press the "Run" button, and the machine will continue to run until it reaches the set number of laps.

★If the machine needs to run for a long time, the counter should be stopped. At this time, "Running laps" will display "STOP"; if you don't want to run for a long time, **press the "stop counting" button again, and the machine** will return to the original counting state.

★If the "set" button is pressed during machine operation, the whole machine will stop running. At the same time, the 10,000 digits of "Set the number of laps" flash, and the values of "Zero A" and "Zero B" are flashing.

★If water cooling is needed, connect the water nozzle of the upper grinding disc.

關鍵詞：控制器電源開關計數器